banner

High-Speed Cannulated Drill S1010 180W 1250RPM

Short Description:

Cannulated fixation punishes an inconsistent drill. A guide wire has to stay centred while the bit cuts cortical bone, torque has to hold through the whole pass instead of stalling at the far cortex, and the handpiece has to come back from the autoclave ready for the next case. The S1010 and S2010 high-speed cannulated drill were built for that narrow job: a hollow brushless shaft, 180 W of output, stepless 0 to 1250 rpm, and a 4.5 mm working channel that takes standard guide wires. This release sets out the specification, the points that decide intraoperative performance, and the supply terms distributors ask about.


Acceptance: OEM/ODM, Trade, Wholesale, Regional Agency,

Payment: T/T, PayPal

Sichuan Chenanhui Tehnology Co., Ltd.is a supplier of orthopedic implants and orthopedic instruments and is engaged in selling them, owns its manufacturing factories in China, which sells and manufactures internal fixation implants Any inquiries we are happy to reply. Please choose Sichuan Chenanhui, and our services will definitely give you satisfaction.

Product Detail

Product Tags

I : Core Application & Clinical Advantages of the High-Speed Cannulated Drill

The high-speed cannulated drill is built on a fully enclosed brushless motor with a hollow axis, so the guide wire runs through the instrument rather than alongside it and the drill follows the wire instead of fighting it. The 4.5 mm channel takes the wires used for cannulated screw fixation, and the chuck, hardened to HRC53, accepts bits from 0 to 8 mm with special diameters on bulk request. Radial runout is held under 0.1 mm and the working noise stays at or below 55 dB, which keeps the bit tracking straight and the theatre quiet on long cases.

Table 1. Technical specification of the S1010 / S2010 high-speed cannulated drill

Item

Specification

Motor type Brushless, hollow axis, fully enclosed, high output
Rotation speed 0-1250 rpm (tolerance -10%)
Output torque >= 7 N.m
Output power >= 180 W
Hollow channel Phi 4.5 mm
Chuck hardness / range HRC53, 0-8 mm bits
Radial runout < 0.1 mm
Noise <= 55 dB
Temperature rise <= 50 C in continuous use
Sterilisation 151 C high temperature and pressure, battery excluded
Host weight 1450 g
Warranty 18 months host, 6 months battery

Intraoperatively the sequence is short: reduce, pass the wire, confirm position on image, then run the cannulated drill over the wire and place the screw. Stepless trigger control lets the surgeon drop speed at the near cortex and pick it up again in the cancellous bone, which is where most thermal damage is created. The kit ships with two 12 V, 2600 mAh lithium packs and a pulse charger that refills a battery in about 60 minutes on AC 100-240 V, so a list of several cases rarely waits on power.

Core clinical merits

1.Wire-guided tracking, not hand alignment. With the wire inside the 4.5 mm channel of this high-speed cannulated drill, the bit cannot wander off the planned trajectory, which shortens fluoroscopy time and reduces the number of passes per screw.
2.Torque that holds through the far cortex. The brushless hollow-shaft motor of this high-speed cannulated drill delivers 7 N.m at up to 180 W, so the bit cuts through instead of stalling and stuttering at the second cortex.
3.Thermal and vibration control. A temperature rise capped at 50 C, noise at or below 55 dB and radial runout under 0.1 mm combine to protect bone from heat necrosis and keep the cut accurate.
4.Autoclavable body. Everything except the battery pack takes 151 C steam sterilisation, so the handpiece returns to the tray through the normal reprocessing route instead of a chemical dip.
5.Built for a full list. At 1450 g the pistol grip stays manageable across consecutive cases, and the dual-battery kit with a 60-minute charger removes the wait between procedures.

Positioning against the rest of the range is straightforward. Plate work that does not need a wire runs faster on the high level bone drill, while K-wire and intramedullary cases are served by the medium-speed cannulated unit. This high-speed cannulated drill earns its place where screw placement has to follow a wire through dense cortical bone. Dimensions for the whole family sit under orthopedic power systems, and the specific handpiece on its product page. Buyers who standardise cannulated drilling across several trays also compare the S1010 with our brushless high-speed cannulated drill before fixing a single platform.

Cannulated Drill S5100
Core Engineering Advantage

Intraoperative Use, Limitations & Service Cycle

1. Intraoperative protocol

  • Reduce the fracture and pass the guide wire under image intensification before the drill is powered up.
  • Run the high-speed cannulated drill over the wire at reduced speed on entry, then increase through the medullary space and ease off again at the far cortex.
  • Keep irrigation on the bit during the cortical pass; the handpiece controls heat at source, but a dull bit will still raise local temperature.
  • Confirm screw length with the depth gauge from the same kit, then place the screw without removing the wire until position is verified.

2. Limitations & common issues

  • The battery pack for the high-speed cannulated drill must never be autoclaved; sterilise the handpiece, chuck and channel only, and keep a charged spare outside the tray.
  • The instrument is not intended for cranial or spinal work, where dedicated micro drills with finer speed control are the correct choice.
  • Noise and heat figures assume a sharp bit and correct feed pressure; forcing a worn bit through cortical bone is the usual cause of complaint.
  • Custom chuck diameters and body colours are a production item, not a stock item, so they add lead time to a first order.

3. Maintenance & service cycle

  • Clean and lubricate the chuck key assembly at the interval set by the hospital's reprocessing policy, and inspect the channel for debris after every case.
  • The host carries an 18-month warranty and the battery 6 months; spare packs, chucks and chargers are supplied separately so a unit is never out of service for a single component.
  • Test reports, quality certificates and packing documents accompany each shipment for local registration files.

Why Global Distributors & Hospitals Choose Our High-Speed Cannulated Drill

✅ Factory-direct supply, no trading layer, with volume pricing on the S1010 and S2010 high-speed cannulated drill handpieces

✅ 180 W, 7 N.m and 0-1250 rpm on one platform, with a 4.5 mm channel and 0-8 mm chuck range

✅ 151 C autoclavable body, with dual batteries and a 60-minute charger in every kit

✅ Batch inspection records, test reports and certificates prepared for tender and registration files

✅ Private colour, logo and packaging for distributors; quality system documents from an ISO 13485 and CE-MDR certified power tool supplier, on request.

Get Wholesale Quotation for the S1010 Cannulated Drill

Email us: cah@medtechcah.com

WhatsApp / Call: +86 15008449628

For a price list, a sample handpiece or a mixed power-tool carton, reach the power tool team through our contact page; units are quoted per handpiece, per kit or per complete set.

FAQ: Common Questions About the Maxillofacial Instrument Kit

Q1: What separates the S1010 from the S2010?

A: Motor, power and speed are identical; the difference is the exterior design and the colour options offered with each. Engineering drawings are available for a side-by-side comparison.

Q2: Can the whole unit be autoclaved?

A: The body, chuck and isolation channel take 151 C high-pressure steam. The lithium battery pack does not and must be removed before sterilisation.

Q3: Which guide wires and bits fit?

A: Any standard wire that passes the 4.5 mm channel of the high-speed cannulated drill, and bits from 0 to 8 mm in the HRC53 chuck. Non-standard diameters are produced on bulk order.

Q4: What is included in the standard kit?

A: One handpiece, two batteries, one chuck assembly with key, one pulse charger, one isolation channel, manual, certificate, acceptance form, repair card and outer case.

Q5: What warranty and spares support is offered?

A: 18 months on the host of the high-speed cannulated drill and 6 months on batteries, with spare chucks, chargers and packs supplied separately and remote technical guidance included.

Q6: Which documents support local registration?

A: Factory audit records, mechanical performance test reports, quality certificates, packing list and commercial invoice, issued with each order.

Video

  • Cannulated Drill S5100
  • Cannulated Drill S6100
  • Core Engineering Advantage

  • Previous:
  • Next:

  • Write your message here and send it to us